Acclimation of Laminate Flooring

Terry Weinheimer | Kevin Weinheimer — Tue, 22 Sep 2009 15:51:06 +0000

The manufacturers of most laminate floors require the cartons of flooring to be acclimated for 48 to 72 hours prior to installation. Acclimation requires conditioning of the flooring material at or near occupancy level. Check the installation instructions to see how they want the material stacked for installation and if the cartons are to be opened or left unopened.

The flooring material needs to be acclimated in the area of installation. This means that if the laminate is to be installed in the family room it should be acclimated in that room.

Storing the laminate flooring in the garage is not acclimation even if the garage is attached. Storage of the material at the store or warehouse of the dealer or installer is not acclimation unless the floor is to be installed in the store or warehouse.

Not all laminate manufacturers require acclimation. If the dealer or installer says it is not necessary to acclimate insist that they show you where the manufacturer states that in writing. Don’t make the manufacturers, dealers or installers problem yours. If they say that the floor does not require acclimation insist on getting this in writing.

When a floor acclimates the product is adjusting to the humidity of the area of installation.

All wet work in the area of installation such as plastering and painting must be completed prior to the start of acclimation. All windows and doors must be installed prior to the start of acclimation. The heating and air conditioning system must be operational at or near occupancy levels. If installing over concrete the concrete should have been tested and found to be at acceptable levels for the installation of the laminate.

When a floor is not acclimated prior to installation it can be hard to click together chipping or damaging the edges of the laminate. A floor that is not acclimated to its environment is more likely to experience problems such as expansion, tenting, squeaking and buckling after installation.

If you are unsure of the laminate manufacturers installation requirements a copy of them is often contained in each carton. Most manufacturers’ installation instructions are also available on LaminateFloorProblems.com

Chips, Dents, Scratches, Gouges in Laminate Planks

Terry Weinheimer | Kevin Weinheimer — Mon, 21 Sep 2009 06:43:37 +0000

Chipped Plank Corners

It is the responsibility of the installer to check all planks prior to installing.

Most all laminate manufacturers take the view that when you install a damaged plank such as one with a chip in it, this becomes your responsibility and not theirs.

Chips at plank corners, especially those that cross over between planks are caused either during the installation process or by a dropped object.

When a chip is located at a single plank corner, this is usually a plank that was installed damaged or became damaged during installation.

An installer must be careful not to install a plank with a chipped corner and if it chips during installation it should be pulled at that time and replaced with a different plank.

Dents, Gouges, Indentations in Laminate Floor

Dents: Like floors of wood and bamboo, laminate floors are subject to denting when a heavy object is dropped on it.

Dents from dropped objects will have stress cracks around the edge of the dent.

Indentations or Gouges: Heavy objects being rolled across a laminate floor can cause indentations or deep gouges.

Laminate Scratching and Scuffing

While some over zealous sales people tend to sell laminate floor as being indestructible most laminate flooring manufacturers state that their floor is scratch resistant. Do not confuse scratch resistant with scratch proof as this is not the same. Usually scratches are not covered by a manufacturers warranty.

Scratch Prevention: Use felt protector on all furniture legs. Keep animal nails trimmed. Place an area rug at all entrances to catch gritty soil and debris. Shoes can trap debris in the soles and scratch a floor. Avoid using hard plastic toys on a laminate floor as hard plastics can abrade a laminate finish.

Caster Damage to Laminate Floor

The proper caster must be used on office and other rolling chairs.

Some manufacturers state that an office chair must have at least 5 casters.

Most laminate flooring manufactures state that rubber casters need to be used as both metal and plastic casters will cause, indentations, abrasions, scratching or scuffing to the surface of the laminate floor.

Improper casters such as metal and hard plastics can also cause chipping along the edge of the planks.

Tapping Block Damage

A tapping block is sometimes used by the installer to join the short ends of the planks.

When a tapping block is used improperly or an objects such as a hammer is used, or planks are kicked together this can damage plank edges.

Laminate Floor Problems - Solutions - Care - Repair » laminate floors